Steel epoxy 24g Daual sryinge_Mix by hand.
Resin and hardener are forced to mix and harden rapidly. After full hardening, it has excellent hardness and endures 650℉. It’s paintable, antirust, waterproof, resistant to most of weak chemicals and has insulation property.
代碼 NE02675
人氣 1014
PB 4 minutes rapid plastic Steel Epoxy is two-part expoxy adhesives. Resin and hardener are forced to mix and harden rapidly. After full hardening, it has excellent hardness and endures 650℉. It’s paintable, antirust, waterproof, resistant to most of weak chemicals and has insulation property. You can mill, sand and drill after it fully hardens.
APPLUCATIONS: It cures fast for quick metal to metal to metal
bonding and repairs, such as gap filling, filling casting blister, water tank, oil tank, pipe, machine, mold, and many materials with cracks, breaks and holes, such as glass, stone, carbon fiber, wood, fiberglass, crack of wall, marble leakage, electrical appliance, craft, adornment, model, fishing tackle, toy, auto parts.
DIRECTIONS FOR USE:
1.Roughen the surface to be joined or repaired with sandpaper. Ensure surface are clean & dry, free dirt, oil, moisture, rust.
2.Break off the end of nozzle. Extrude equal amount of Resin & Hardener onto a clean surface. Mix thoroughly. 【Mix ratio=1:1. Wrong ratio or unequal mixing may result in bad hardness.】
3. Finish the operation within 3 minutes. Solidify in 4 minutes. Full bond strength is reached after 24 hours. 【when the temperature below 10℃,the hardening time is longer.】
CAUTIOUSLY:
Irritation for eyes, skin respiratory system. Previous protection is recommended. For skin contact, wipe off contamination and wash thoroughly with soap and warm water. In case of eye contact, rinse with plenty of warm water and get prompt medical attention. If swallowed, seek the physician. 【KEEP OUT OF REACH OF CHILDREN】
Improper use may damage the surface. Be sure to test the material as well as compatibility before using. Be sure to dump the waste in a permitted environment under the law.
CONTAINS: Epoxy Resin,Polymercaptan.
PB 4分鐘塑膠鋼是一種高分子(油灰狀) 產品，AB兩劑強迫混合快速硬化，操作時間急迫，可在緊急情況下，快速修補黏合，完全硬化後，硬度特佳，耐高溫650℉，防水不生鏽，可抗大多數化學侵蝕。可行車金先、削、磨、鑽，絕緣(不導電)，可上漆。
適用用途：金屬鑄件沙眼、桶糟、油箱、水箱、管路配件、機械、模具之修補。任何金屬製品損壞、撞痕、孔洞、斷裂、玻璃、石材、陶瓷、碳纖維、木材、玻璃纖維、居家水泥裂縫、大理石掉落、電器製品、藝品、裝飾、模型、釣具、玩具、汽機車零件、運動器材，均可修補黏合。
使用方式：
1.將欲修補黏著的表面用砂紙磨予粗糙，確保表面潔淨乾燥。
2.將出口處之壓板壓斷，即可擠出A、B兩劑，均勻攪拌混合。【混合比例1:1，誤差大或混合不均勻會照成硬化不良。】
3.請再90分鐘內完成黏合固定作業。90分鐘硬化，最佳黏合強度須經24小時。
【氣溫低於10℃以下則硬化時間較長】
注意事項:
請戴護具施工，誤觸皮膚時，請用肥皂和清水搓揉剝離或用(乙醇)酒精擦拭即可，誤入眼睛時不可搓揉，立刻用大量清水沖洗數分，且就醫診治，若誤食立刻送醫治療。【存放兒童取扱不到的地方】
不當使用，可能會造成物品受損，務必事先測試接著物材質及接著強度，測試滿意才使用本產品進行施工黏合。本產品廢棄處理方式，須在政府核可廢棄處理設備處理。
主要成分：環氧樹脂、聚醯醇樹脂。
產品規格：PE瓶包裝